The ZYYX printers have some parts that will not last forever, and needs to be replaced when they are worn-out or has reached their life-span.
ZYYX Fume Filter™ Pack
This filter package will give you a fume-free printing experience for roughly half a year, as the Fume Filter should be replaced every other month.
Package of 3 filters for ZYYX/ZYYX+
(Note: Newer ZYYX + has the same thicker filter as ZYYX Pro, see below)
The ZYYX+ Build-Plate uses a premium borosilicate glass base plate laminated with a custom plastic surface.
This build-plate surface enables printing with most of the currently available filament types without any need for a heated plate or adding temporary materials to the plate surface.
The build-plate is held in place with three neodymium magnets, making it easy to remove the plate before removing the prints.
A ZYYX+ Build-Plate is supplied with every ZYYX+ 3D printer, and this will last about 6 months under normal usage. After this time the plate surface will have some wear and to ensure good adhesion the plate should be replaced.
Since 2018, the top surface is black instead of white, and the top surface can be purchased separately.
Package of 1 ZYYX/ZYYX+ Build-Plate.
The ZYYX+ hotend is made out of brass, which transfers the heat from the heater to the filament. Set screws to fixate the heater cartridge and temperature sensor are included.
A ZYYX+ Hotend is supplied with every ZYYX+ 3D printer, and this will last for very long time under normal usage and continuous cleaning. .
Package of 1 ZYYX/ZYYX+ Hotend.
Note! Please note that the older ZYYX Classic uses a shorter nozzle. In order for the new nozzle to fit, you may need to drill the aluminum block through and cut away the lower part of the clamping arm. Contact ZYYX for details.
ZYYX Pro Fume Filter Pack
This filter pack allows for fume-free printing for roughly half a year, as the Fume Filters should be replaced every other month.
It consists of two parts, a black part consisting of activated carbon which absorbs odours and a white part, which is a so-called HEPA filter. The HEPA filter also captures particles.
This filter size is also used by some ZYYX+ printers manufactured 2018 and later.
You can also use these in older printers, but then need an extension frame for the filter holder. Contact ZYYX for details.
Package of 3 filters for ZYYX Pro or newer ZYYX+.
ZYYX Pro Standard Build-Plate
The removable ZYYX Pro Standard Build-Plate is made specially for 3D printing in engineering materials such as proNylon™ and proCarbon™. This build-plate surface enables easy 3D printing in our engineering materials without any need for a heated plate or adding temporary materials to the plate surface.
A ZYYX Pro Standard Build-Plate will last about 6-12 months under normal usage. The plate even works better when it shows some wear, but should be replaced if the top surface displays larger holes or the glass is cracked.
Package of 1 ZYYX Pro Standard Build-Plate
ZYYX Pro Multi-Material Build-Plate
Our removable ZYYX Pro Multi-Material Build-Plate is created to allow printing in other than our engineering materials. This build-plate is not suitable for the engineering materials, but offer optimal printing for our ZYYX PLA, ZYYX ABS, ZYYX FLEX among others.
A ZYYX Pro Multi-Material Build-Plate will last about 6 months under normal usage. After this time the plate surface will have some wear and to ensure good adhesion the plate should be replaced.
Since 2019, the top surface is thinner and replaceable, and the top surface can be purchased separately. One extra top sheet is included with each build-plate.
Package of 1 ZYYX Pro Multi-Material Build-Plate with one extra top sheet.
ZYYX Pro SwiftTool™ Carbon0.6
This is a 0.6 mm hardened steel nozzle that can be used with any filament but that is optimized for the use of abrasive filaments, like proCarbon or proGlass. These are strong carbon fiber and glass fiber reinforced nylon filaments suitable for heavy duty applications. Note that these materials only should be used with this kind of nozzle.
ZYYX Pro SwiftTool™ Multi-Material
Set of standard SwiftTools for use with non-abrasive filaments like PLA, ABS, or proNylon™. They can be purchased together or as a kit.
Red=Multi0.2 mm (This SwiftTool is 4-8 times slower than Multi0.4 when printing the same model.)
Yellow=Multi0.4 mm (Standard size)
Green=Multi0.8 mm (This SwiftTool is 4-8 times quicker than Multi0.4 when printing the same model and may be used for quick draft prints)
Note that these nozzles never should be used with proCarbon™ or proGlass™.